Replacing uPVC Window Handles

The replacement of window handles made of upvc is an easy task. It is crucial to make sure that the new handle is fitted into the spindle cutout in the window mechanism.

If you follow the steps below any cockspur handle can fit most windows. The most important factor is the step size of the handle.

What to Look For

A lot of windows in the UK come with uPVC handles and, over time, they can begin to show signs of wear and tear. If this occurs, the handle may become loose or difficult to operate, which makes it essential to replace it. This is a fairly easy task that is achievable by anyone who is comfortable using basic hand tools.

The first thing to do is ensure that the handle is securely connected to the window frame and is in the open position. The next step is to locate the pins or screws that hold the handle. They are usually located on the inside of the handle. They can be removed with a screwdriver, or pliers.

When the handle is loose, gently pull it away from its hinges. The next step is to find a replacement handle with the same design and size. This can be accomplished in the DIY store or on the internet. The process should take about five minutes and requires a screwdriver.

The most important thing to consider when replacing a uPVC window handle is the step height. This is the distance between the handle's base and where it sits within the frame of the window. This is a standard measurement and you should check the step height before ordering the replacement handle.

There are a variety of sizes based on the kind of handle. Inline handles for uPVC windows generally feature lug centers of 31mm as well as handles with cockspur with 43mm centres. Tilt and turn handles are typically found on uPVC windows, and they come with a unique design that allows the window to be tilted in for ventilation, and then rotated to open the window completely.

The most frequent breakage in uPVC handles is that they crack inside instead of breaking away from the base section. This makes it difficult to open. It is important to ensure that the replacement handle has the same spindle as the original one.

Remove the old upvc door handles Handle

If the handles on your windows are damaged or improperly installed, they could cause double-glazed windows to not open or close correctly. They may even become stuck. This can be caused by many reasons, including general wear and tear on the metal handle or corrosion. In these situations it is essential to replace the window handle as soon as you can to prevent further damage or loss of functionality.

When replacing upvc windows handles it is recommended to remove the old handles from the window. To do this, start by getting rid of the screw that is covered when the handle is in the closed position. Once you have removed that screw, you can take off the handle. It is a good idea to make use of an electric screwdriver for this since it will make the task much easier and quicker.

It is also important to note that the handles' screws could be hidden behind plastic caps, therefore it is a good idea to use an Stanley knife to the screws and take them off. After removing the handle, you'll need to check the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. This is crucial as you'll need to measure the length of the spindle of the old handle to make sure it matches the size of the window mechanism and the handle spindle that has been cut out.

The various types of window handles made of upvc are: Espag handles, which have a central screw and will turn left or right; Cranked handles that have two screws and are typically found on tilt and turn upvc windows; and Spade handles, that have an arm that is flat and can be put on either side of the window. It is easy to replace the handle when you've located one that is suitable. Simply screw it into the frame, and ensure that the spindle is properly inserted into the lock mechanism. Once that is done, it should be tightened to the window frame and your replacement window handles made of upvc should be secure.

Take a measurement of the Spindle

If you're looking to replace a handle made of upvc that has collapsed, it's likely the spindle that holds it in place is damaged or loose. In some cases you can tighten the spindle by using a screw or pin. In other instances, it may have to be replaced completely. There are several kinds of window handles made of upvc. There are three kinds of handles: inline espagnolette, tilt-and-turn, and cockspur. Each kind has a distinct method for installing and removing the handle.

It is important to measure the handle before purchasing an alternative. This will ensure that the handle will fit the window in a proper manner and will be of the correct size. Fortunately, all handles follow industry standards of sizing making it fairly easy to find the right size.

To determine the size of the handle, turn the window to the open position. You should be able to see the size of the screw or pin that holds the handle. Then you can use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a replacement one that is exactly the same size.

The step height of a upvc window handle is another factor to consider when purchasing an alternative. The step height is the distance from the base of the handle to where it sits on the frame. It is typically about 21mm or 9mm for aluminium and uPVC. Dropping objects into the gap will allow you to observe how far the handle extends before it reaches an obstruction.

Cockspur handles for double glazed doors may have different backsets, based on the type of window you put them in. Inline espag external door handles and locks have a standard height of 43mm from centre to centre (2 fixing points). Cockspur handles, however they have different backsets dependent on the design of the window they're in. This is due to the fact that they have a spur that extends from the handle and locks over a cockspur wedge striker plate.

Fit the New Handle

If you've decided to replace the handle, ensure that it is aligned with the screw holes on the patio door handle and secure it using the screws provided. If you're replacing the latch lever, it can be installed in a similar way to the main door handles handle. After that, attach the patio door handle locks trim to conceal the screws for mounting and finish the job.

Tips: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is level with the ground. Then use to tap the narrow end. Be careful not to damage the handle or the spindle.