upvc replacement door handles (fakenews.win)

The handles on your doors are worn out with time and require to be replaced. It is essential to match the dimensions of the handles that were previously used when replacing them.

The three measurements you need to examine are the top screw position, lever and key hole sizes. Use the size guide to assistance in this.

Inline Lever/Lever

A lever handle or lever is a contemporary door handle designed to work with new or replacement doors. This kind of handle is available in a variety of designs and finishes. A number of manufacturers offer this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The door handles of uPVC/Composite are made of robust materials and are suitable for multi point lock doors that require a heavy duty design. The handles are inline and run from the same spindle and screw fixings. They are easily installed on existing or new uPVC/Composite doors.

The design of the sprung lever allows the handle to be set and angled to provide a comfortable grip and is suitable for all users. The handle has been tested for endurance up to 200,000 cycles, this helps to ensure the quality of the finish and the performance of the handle over time. The sprung lever can be reduced to accommodate more locks. This is especially useful for doors with narrower frames, in which the cylinder is further back. A shortened lever can also be used for doors that have a latch that can be opened by the thumb inside.

Lever Pad

The lever pad upvc handle is distinct from the lever handles found on most doors. These handles can work off one single spindle (inline) or independently from each side by using two offset spindles or inline (pad). They are typically used on UPVC double glazed doors and come in many variations & finishes.

The handles for bifold doors have been tested to a minimum of 200k cycles and are available in a variety of finishes including White Silver, Chrome, & Gold. The finish is BS EN 1670 Grade 5 and is resistant to corrosion. This gives the handle a high performance and durability to serve its intended purpose.

All UPVC levers for handles come with a spindle, screws and can be mounted on a uPVC door. The 211mm backplate fixation centres permit a larger handle, which is usually beneficial when replacing an old or damaged multi-point door lock mechanism. The handle levers are spring-loaded, thereby solving the issue of handles hanging from their horizontal position when not in use.

When selecting the replacement double glazing window handles UPVC handle and spindle, it is essential to match the dimensions of the PZ of the multipoint lock as well as the uPVC door. This measurement can also be called 'handle centres' or cylinder centres'. It is important to match the correct handles.

Once you have the correct PZ size, you'll have to ensure that the lever pads and push pads are in a suitable shape for the American with Disabilities Act (ADA) compliant handles that you require for your doors. These are typically round or square, with an internal lever and an external door handles push pad.

The majority of UPVC Lever Pads we offer are sprung. This means that they return to a horizontal position after not in use, rather than hanging and possibly being stuck in the frame. This prevents drafts and cold air from entering a home. The majority of UPVC lever pad style handles come in both left and right handed models, allowing them to be put on either side of doors.

Euro Cylinder

Cylinder locks are typically found on uPVC doors, but they can also be used on other types of doors. Cylinder locks are operated by a key which unlocks the cylinder's case. This exposes pins that can be aligned to the pins in the lock, and permit them to turn the camera that rotates, opening the door. Euro cylinders can be fitted with up to six pins. External and internal doors require different levels of security.

The selection of a cylinder is essential. It depends on the amount of use your doors and handles receive. External doors, for example are required to be fitted with cylinders with greater security, whereas internal doors can be secured using a standard cylinder. Additionally, certain cylinders are available with extra features which can enhance security even more, like anti-drill and anti-bump characteristics.

To ensure that the euro cylinder is the right size for your door, it should be measured accurately. The cylinder should be measured from the hole in the center of the fixing screw to each end of the cylinder including the thumb turn if you have one. It is best to do this while the lock is in place however, if this is not feasible, you can take it off and remove it to measure. It is essential to avoid having a extension of the cylinder beyond the handle or escutcheon. This could make it vulnerable to snapping lock attacks.

Most modern cylinders are made with bump and anti-drill features built into their design. These features are designed to minimize the chance of a attack by forcing the cylinder to rotate in a different direction. This can to deflect an attack and protect your door.

There are cylinders that are designed to resist snapping. This is an increasingly common kind of attack on cylinders, which is where the break line of the lock is targeted by a tool that is specially designed to break off the front of the cylinder to allow the door to open. This is a much faster and simpler method to gain access than the use of a multipoint locking system. It also leaves no evidence of the break-in which can delay insurance claims.

Spring Cassette

The spring cassette is positioned in the base of the door handle backplate, supplying a spring-loaded solution and returning your multipoint lock handles to their original position after usage. Previously a lot of handles didn't have a spring built into them, and without it they can droop or drop once the locking mechanism has been disengaged. This simple component is the most effective way to solve this issue. It also prevents your door from getting stuck in the open or closed position, as they are difficult to close manually.

These spring cassettes are specifically designed for use with sprung multipoint locks They will not work with multipoint handles that are not sprung and you must have a hole specifically cut in your backplate to allow these to fit (please look at the image for a technical diagram). They are a replacement for broken or missing cassettes within the door handle backplate of many brands of uPVC doors. They are sold as one unit. They feature a square cut out that can accommodate an 8mm shaft.

These spring cassettes offer an excellent value solution to the issue of door handles that have become sagging. They are simple to install and will increase the lifespan of your uPVC door. For more information on our range of uPVC spares and accessories you can get in touch with our team. We are here to help and happy to provide professional advice.