This Week's Top Stories About Door Lock Change Door Lock Change > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change your door lock is an easy and affordable way to improve the security of your home. However, this process is not for all. It requires a certain amount of skill and perseverance.

The cylinder is contained within the knob body. The cylinder is responsible for recognizing the key when it is put into the lock.

Take off the lock that was previously used.

The first step is to remove the old lock. It is a fairly straightforward process, however you should keep some things in your mind. First, ensure that your new lock is the correct size for your door. This will ensure it fits securely, and doesn't leave a gap in the deadbolt or latch.

After you have removed the latch plate, you will need to look for two screws or bolts in the casing's interior that hold the casing together with the two halves of the lock. Unscrew them using the help of a screwdriver, and then remove the lock from the door. If you are using a mortise locking system there is a set screw that binds the handle to the spindle. Remove the doorknobs by unscrewing this screw with the help of a screwdriver.

You should also remove the deadbolt latch and latch plug from the hole in the door jamb. Install your new lock. If you are replacing a mortise lock, you should also determine the distance between the lock case and the door's edge to ensure that the new lock will be able to fit.

You might want to change your lock for various reasons, for instance, if you suspect that someone else has the key or you have an incoming roommate. In any case, you can save money by removing the lock yourself instead of paying a professional to do it. It is much easier than people think and can be done in a matter of a few minutes.

Begin by taking the handle and trim from your door. Then, pry the trim loose using a screwdriver that is flat. You should be able twist off the majority of it. In some cases you may be able to remove the handles completely. Next, examine the handle for a tiny pinhole on the inside. Then insert a straightened clip into it. This will activate the release mechanism, which allows you to remove the handle. Next, examine the interior side of the lock for a small tab that you can press using a screwdriver that is flat. After the spindle has been removed, you are able to remove the cylinder and housing.

Making a decision on a new locking system

When it comes time to pick a new lock there are a lot of options. Look at different kinds of locks, and select one that fits the style of your door. Take into consideration the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole in the frame of the door frame). Also, make sure to choose a lock that will be able to fit the door's thickness and swing.

The majority of door locks have been assessed by BHMA and the American National Standards Institute to give you an idea of how they will withstand use and how difficult to pick or disable. A grade 3 lock may be the best choice for a peaceful rural apartment complex, while an entry grade lock could be more able to withstand the traffic that is frequented by a storefront on a busy city street.

Most smart door locks require a digital key code to open. If you're worried about hacking or other security concerns seek out a professional locksmith or the local police department for assistance.

Replacing the cylinder

If the cylinder of your door lock is broken or damaged you can repair it in a matter of minutes by completing a do-it-yourself project. It is important to select the correct cylinder and follow all instructions. The first step is to remove the knob or handle if there is one, then unscrew the trim around the base of the lock cylinder by using the aid of a screwdriver. After the trim has been removed, you can take off the screws that hold the cylinder with the flathead. The cylinder is then gently pulled away from the door.

Before you install the new cylinder, be sure it's the correct length for your door. With a tape measure, determine the distance between the cylinder's center and its left and right sides. Then, buy an additional cylinder using the same measurements. This will prevent cylinders from snapping when doors are kicked or the key gets stuck inside.

If you have a suitable replacement cylinder, put it into the door and turn the key. This will ensure that the cylinder is aligned with the carrier, which is typically located on the outside of the lock. Then, loosen the set screws which should be a couple of turns in the head. You will also need to loosen the screw at the edge of the door that holds the case in place, in the event that there is one.

You can replace the old lock cylinder with a new one by slipping it into the case, and then tightening the set screws. You should also reinstall the bracket that connects the cylinder to the lock indicator stem that you can do by removing three tabs on the back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the back of the cylinder. Then, you need to reinstall the strike plate and latch plate as well as the retaining ring that is connected to the top lock the cylinder.

Installing a new lock

Begin by measuring the door's width if you are replacing an existing lock. Most locksets for residential use are designed for a door thickness of 1 3/8 - 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll need a stronger door kit. This will require longer screws as well as an extended spindle extension or the tail piece for door knobs.

Most double glazed window lock repairs near me glazing upvc window lock replacement locks replace; view Chessdatabase, come equipped with a detailed installation guide to assist you. Read the instructions carefully prior to beginning the process to make sure that you are following all the steps. The guide will give you a good idea of the amount of skill that is required to complete the task. It is possible to ask a person who has worked with locks for assistance if you are changing a lock the first time.

It's a good idea to seal the openings of the old lock before installing the new upvc window lock repair. This will keep the screws from falling out of the holes and will safeguard any tile you may have put in the area. This will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip painter's tape designed to be used to protect your painter's tape, but you can also use gaffer's tape as well as masking tape in the event that you have it.

After taking off the screws that connect the lock's interior half to the outside, take the lock off immediately. This should be done swiftly to prevent the lock from accidentally closing and damaging the mechanism.

If your new lock has an latch bolt, install the new latch bolt into its upper cross bore. Make sure that you place it in the correct location, which is indicated by an arrow. Next, fit the latch plate over the bolt and screw it into the correct position.

Finally, screw the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it several times to make sure that it extends all the way into the strike plate and is secure. If you're using an electronic smart lock, be certain to follow the instructions to program it. This involves downloading an app and creating an email address, verifying your identity, and accessing the wireless network to connect your device.